WL WN580N2 N300 Extender Setup

You are currently viewing WL WN580N2 N300 Extender Setup
WL WN580N2 N300 Extender Setup

By performing the WL WN580N2 N300 extender setup process you will easily extend the range of any existing router WiFi signal. On this page, you will get full knowledge about this Wavlink extender product. So read this page and follow the instructions carefully.

Benefits Of WL WN580N2 N300 Extender Setup

Listed Down are the benefits for WL WN580N2 N300 Extender Setup:

  • Doubles the coverage of the router’s WiFi signals.
  • Connectivity for any device through its USB port.
  • Operates under WPA-PSK/WPA2-PSK encryption.
  • Easy connection to any router by pressing the WPS button.
  • Supports simultaneous connection of multiple devices.
  • Primarily designed for tablets, smartphones, and other portable electronic gadgets.
  • The compact size of the Wavlink N300 extender makes it easy to carry.
  • Also known as a USB WiFi extender.
  • Eliminates WiFi dead zones after installation.

WL WN580N2 N300 Extender Setup via WPS

Here are the steps for WL WN580N2 N300 Extender Setup via WPS:

  • Plug the extender into a power outlet near your Wi-Fi router
  • Switch on the extender using the power button if it has one.
  • Locate the WPS button on the extender. It’s usually labeled as “WPS” or something similar.
  • Press and hold the WPS button for a few seconds until the WPS LED starts blinking
  • Within 2 minutes, go to your Wi-Fi router and find the WPS button on it.
  • Press and hold the WPS button on your router for a few seconds
  • The WPS LED on the extender should now stop blinking and become solid, indicating a successful connection.
  • If possible, move the extender to the desired location, keeping it within the range of your router’s Wi-Fi signal
  • On your device (computer, smartphone, etc.), scan for available Wi-Fi networks.
  • Connect to the Wi-Fi network broadcasted by the extender. The network name (SSID) is often similar to your main router’s network with “_EXT” or something similar appended.

How To Login Into Wavlink Extender

  • Begin by opening a Safari web browser.
  • Enter the web address “wifi.wavlink.com” or the IP address “192.168.10.1” in the location field.
  • Provide the necessary details, including the username and password, to access the Wavlink extender login page.
  • Once entered, you will successfully land on the Wavlink extender login page.

WL WN580N2 N300 Extender Setup: Guide

  • Start by inserting the Wavlink extender USB port into the laptop’s USB port.
  • Ensure that your laptop, to which the extender is connected, is in close proximity to the host router.
  • Press the WiFi Protected System button on the extender.
  • Within two minutes, press the WPS button on the main router.
  • Subsequently, both devices will display a solid blue LED, indicating successful synchronization.

Therefore, the WL WN580N2 N300 Extender Setup process is now complete. If you encounter any issues, refer to the following troubleshooting tips to resolve them

WL WN580N2 N300 Extender Setup via WPS

WL WN580N2 N300 Extender Setup Issues
You can troubleshoot and resolve WL WN580N2 N300 Extender Setup with the following solution tips:

Tip 1: Check Wired Connections to N300 Extender

Examine all wired connections associated with your Wavlink extender. Replace any damaged cables promptly. Once the cables are replaced, check your computer or laptop. If you observe a stable internet connection on your device, the issue with the WL WN580N2 extender is likely resolved.

Tip 2: Verify Extender Placement

Optimal placement for your Wavlink WiFi extender is in the central area of your home or office. Ensure that the extender is within the range of the router, with a distance between them not exceeding 10 to 15 feet. This helps in avoiding potential issues with the Wavlink extender.

Tip 3: Remove Extra Devices

Often, improper functioning of the Wavlink extender can be attributed to multiple WiFi devices connected to the Wavlink extender network. Remove any additional devices that are not in use to optimize the performance of your Wavlink extender.

Tip 4: Update Wavlink N300 Extender Firmware

To address the extender not working issue, consider upgrading the firmware. Follow these steps if you are unsure how to update the software of the Wavlink extender:

  • Open a web browser on your mobile phone and enter “wifi.wavlink.com” in the search box.
  • The Wavlink WiFi N300 extender login page will appear on your display. Enter the required credentials as prompted.
  • Access the Wavlink extender settings by clicking on the administration option.
  • Under the administration option, select the software update option and click on “Wavlink extender software updates.”
  • If the issue persists even after trying the above tips, proceed to the following method.

Tip 5: Reset Wavlink Extender

  • Locate the reset hole button on the back of the extender.
  • Press the button using a paperclip for a few seconds.
  • All LEDs on the Wavlink extender device will turn off.
  • After this reset, your Wavlink N300 extender device will be completely reset.

Note: After resetting the Wavlink WiFi extender, you will need to go through the WL WN580N2 N300 extender setup process again.

We hope this post provides you with valuable information on the login and setup process for the WL WN580N2 N300 extender device. If the troubleshooting tips above do not resolve your Wavlink extender issue, please feel free to seek further assistance.

Common Wavlink Extender Setups

Some Issues You Might Face

  • Wavlink login issues
  • Wifi.wavlink.com access problems
  • Wifi repeater malfunction
  • Wifi extender not functioning
  • Ethernet extender not operational
  • Issues with wifi extender password
  • Wavlink router malfunction
  • Unable to connect to IP address
  • Addressing Wavlink yellow light problem
  • Resolving Wavlink red light issue

Leave a Reply