WiFi 5 · AC750

Wavlink AC750 Setup Guide

Set up your Wavlink AC750 extender (WN575A2 / WN576A2 / WN577A2 / WN578B2) using ap.setup or 192.168.10.1. 750Mbps dual-band extender range. The Aerial series with external antennas for better coverage across multiple rooms.

ap.setup 192.168.10.1
📞 Call for Help: +1-323-507-3713

Whether you say "ap setup", "AP setup", or "ap.setup" — they all refer to the same process: opening your Wavlink extender's configuration page to connect it to your home network.

Wavlink AC750 extender — setup at ap.setup or 192.168.10.1 Wavlink Wavlink AC750 WiFi extender specifications: 750 Mbps speed, Dual-Band 2.4GHz + 5GHz. Access setup at ap.setup or 192.168.10.1 after connecting to the _Ext WiFi network. ap.setup Wavlink AC750 Speed: 750 Mbps Band: Dual-Band 2.4GHz + 5GHz Setup: ap.setup or 192.168.10.1 Login: admin / admin · Network: WiFi name ending in _Ext
Wavlink AC750 extender — setup at ap.setup or 192.168.10.1

What Does "AP Setup" Mean? (ap.setup Explained)

The phrase ap setup (also written as ap.setup) refers to the process of configuring a Wavlink WiFi range extender using the device's built-in web interface. The ap setup page is accessed by typing ap.setup or 192.168.10.1 in your browser address bar — this is known as the AP Setup Wizard or ap setup login page.

"AP" stands for Access Point — the operating mode used by Wavlink extenders when they relay your router's WiFi signal. The ap setup interface lets you configure the extender's WiFi name, password, operating mode (Repeater or AP), and advanced settings like DHCP, channel, and security.

💡 Key terms you'll see during ap setup: ap.setup (the URL), 192.168.10.1 (the IP address), AP Setup Wizard (the configuration tool), and _Ext (the suffix on the extender's default WiFi network name).

Wavlink AC750 Specifications

Applies to model(s): WN575A2 / WN576A2 / WN577A2 / WN578B2

SpecificationDetail
Speed750Mbps (2.4G+5G)
BandDual-band
WiFi Standard802.11ac (WiFi 5)
Setup URLap.setup / 192.168.10.1
Default Loginadmin / admin
ModesRepeater, AP, Router

How to Set Up Wavlink AC750 via ap.setup

Follow these steps to complete the setup on any device.

  1. Plug your Wavlink AC750 extender into a wall outlet near your main router. Wait for the LED to turn solid green (about 90 seconds).
  2. On your phone or laptop, open WiFi Settings and connect to the network ending in _Ext (e.g. Wavlink_Extender_Ext or Wavlink_AC750_Ext).
  3. Open Chrome, Firefox, or Safari. Click the address bar at the top of the browser window.
  4. Type ap.setup and press Enter. If the page doesn't load, use 192.168.10.1 instead.
  5. Log in with username: admin and password: admin.
  6. The AP Setup Wizard will launch. Select your home WiFi network from the list.
  7. Enter your home WiFi password and click Connect or Apply.
  8. Wait 2 minutes for the extender to restart and sync with your router.
  9. Move the extender halfway between your router and the dead zone area.
  10. Reconnect your devices to the extended network. Setup is complete!
💡 Placement tip: For best results, position your AC750 extender where it still receives at least 50% signal strength from your main router.

WPS Setup Method (Quickest)

No browser needed. Requires a WPS button on your router.

  1. Place your AC750 extender near your router and power it on.
  2. Wait for the solid green LED.
  3. Press the WPS button on the extender. The WPS LED blinks.
  4. Within 2 minutes, press the WPS button on your main router.
  5. Both devices blink, then solid green = connection successful.
  6. Optionally log into ap.setup to customise the extended network name.
⚠️ Some ISP-provided routers have WPS disabled. If no connection after 3 minutes, use the manual ap.setup method above.

How to Reset Wavlink AC750 to Factory Settings

  1. Ensure the extender is powered on.
  2. Locate the Reset button on the back or bottom of the device.
  3. Press and hold with a pin for 10 seconds until LEDs flash.
  4. Wait 2 minutes for full reboot.
  5. Reconnect to the default Wavlink_Ext WiFi and log in via 192.168.10.1 with admin/admin.

FAQ — Wavlink AC750 Setup

What is the ap.setup address for Wavlink AC750?

Type ap.setup or 192.168.10.1 in your browser address bar while connected to the extender's _Ext WiFi network. Both open the same configuration page.

What is the default login for Wavlink AC750?

Default username: admin, default password: admin. These credentials apply to all Wavlink extender models.

How do I update the firmware on Wavlink AC750?

Log in to ap.setup, go to Advanced › Firmware Update, download the latest firmware for model WN575A2 / WN576A2 / WN577A2 / WN578B2 from wavlink.com, and upload the file. Never cut power during an update.

ap.setup is not opening on my Wavlink AC750

Make sure you're connected to the extender's _Ext WiFi. Type http://ap.setup with http:// to prevent https redirection. Alternatively use 192.168.10.1 — it's more reliable and opens the same page.

Related Guides

ap.setup Setup GuideMain Wavlink setup guideNot Working? 10 FixesFix ap.setup problemsLogin Page HelpLogin credentials & recoveryAll Wavlink ModelsBrowse all model guides