Wavlink AC600 Setup Guide
Set up your Wavlink AC600 extender (WN570HA1) using ap.setup or 192.168.10.1. 600Mbps dual-band compact extender. Budget-friendly with solid coverage for small apartments.
Whether you say "ap setup", "AP setup", or "ap.setup" — they all refer to the same process: opening your Wavlink extender's configuration page to connect it to your home network.
What Does "AP Setup" Mean? (ap.setup Explained)
The phrase ap setup (also written as ap.setup) refers to the process of configuring a Wavlink WiFi range extender using the device's built-in web interface. The ap setup page is accessed by typing ap.setup or 192.168.10.1 in your browser address bar — this is known as the AP Setup Wizard or ap setup login page.
"AP" stands for Access Point — the operating mode used by Wavlink extenders when they relay your router's WiFi signal. The ap setup interface lets you configure the extender's WiFi name, password, operating mode (Repeater or AP), and advanced settings like DHCP, channel, and security.
ap.setup (the URL), 192.168.10.1 (the IP address), AP Setup Wizard (the configuration tool), and _Ext (the suffix on the extender's default WiFi network name).Wavlink AC600 Specifications
Applies to model(s): WN570HA1
| Specification | Detail |
|---|---|
| Speed | 600Mbps (2.4G+5G) |
| Band | Dual-band |
| WiFi Standard | 802.11ac (WiFi 5) |
| Setup URL | ap.setup / 192.168.10.1 |
| Default Login | admin / admin |
| Modes | Repeater, AP |
How to Set Up Wavlink AC600 via ap.setup
Follow these steps to complete the setup on any device.
- Plug your Wavlink AC600 extender into a wall outlet near your main router. Wait for the LED to turn solid green (about 90 seconds).
- On your phone or laptop, open WiFi Settings and connect to the network ending in _Ext (e.g. Wavlink_Extender_Ext or Wavlink_AC600_Ext).
- Open Chrome, Firefox, or Safari. Click the address bar at the top of the browser window.
- Type
ap.setupand press Enter. If the page doesn't load, use192.168.10.1instead. - Log in with username: admin and password: admin.
- The AP Setup Wizard will launch. Select your home WiFi network from the list.
- Enter your home WiFi password and click Connect or Apply.
- Wait 2 minutes for the extender to restart and sync with your router.
- Move the extender halfway between your router and the dead zone area.
- Reconnect your devices to the extended network. Setup is complete!
WPS Setup Method (Quickest)
No browser needed. Requires a WPS button on your router.
- Place your AC600 extender near your router and power it on.
- Wait for the solid green LED.
- Press the WPS button on the extender. The WPS LED blinks.
- Within 2 minutes, press the WPS button on your main router.
- Both devices blink, then solid green = connection successful.
- Optionally log into
ap.setupto customise the extended network name.
How to Reset Wavlink AC600 to Factory Settings
- Ensure the extender is powered on.
- Locate the Reset button on the back or bottom of the device.
- Press and hold with a pin for 10 seconds until LEDs flash.
- Wait 2 minutes for full reboot.
- Reconnect to the default Wavlink_Ext WiFi and log in via
192.168.10.1with admin/admin.
FAQ — Wavlink AC600 Setup
What is the ap.setup address for Wavlink AC600?
Type ap.setup or 192.168.10.1 in your browser address bar while connected to the extender's _Ext WiFi network. Both open the same configuration page.
What is the default login for Wavlink AC600?
Default username: admin, default password: admin. These credentials apply to all Wavlink extender models.
How do I update the firmware on Wavlink AC600?
Log in to ap.setup, go to Advanced › Firmware Update, download the latest firmware for model WN570HA1 from wavlink.com, and upload the file. Never cut power during an update.
ap.setup is not opening on my Wavlink AC600
Make sure you're connected to the extender's _Ext WiFi. Type http://ap.setup with http:// to prevent https redirection. Alternatively use 192.168.10.1 — it's more reliable and opens the same page.